- 您现在的位置：买卖IC网 > Sheet目录303 > 844USB (B&K Precision)DEVICE PROGRAMMER USB INTERFACE
buffer content to project file. Data required for device are stored in file c:\15001-
25001\file_10.bin. Project file will be stored at c:\projects\project_10.eprj.
Following command line parameters should be specified to realize wished operation:
pg4uwcmd.exe /loadfile:c:\15001-25001\file_10.bin /saveproject:c:\projects\project_10.eprj
When PG4UW receives the commands, it will do following procedures:
1. loads data file c:\15001-25001\file_10.bin
2. saves the currently selected device settings and buffer data to project file
c:\projects\project_10.eprj
If the result of operations performed is OK, PG4UWcmd application will return ExitCode (or
ErrorLevel) value 0.
If there are some errors (can not load file or save to project file), PG4UWcmd application will
return ExitCode value equal or greater than 1.
Note: When using the above commands, user must be sure the PG4UW is not performing
any device operation, for example device programming. If the PG4UW is busy, it will refuse
the commands and returns error status (ExitCode equal or greater than value 1).
Hardware
Due a large variety of parallel port types, a case may occur when the programmer cannot "get
concerted" with the PC. This problem may be shown as none communication between the PC
and the programmer, or by unreliable communication. If this behavior occurs, try to connect
your programmer to some other PCs or other parallel ports near you.
If you find none solution, please document the situation, i.e., provide us an accurate
description of your PC configuration, including some other circumstances bearing on the
problem in question, and advise the manufacturer of your problem. Don’t forget please enter
of PC type, manufacturer, speed, operation system, resident programs; your parallel port I/O
manufacturer and type. Use please Device problem report form for this purpose.
Warning:
Class A ITE notice
Devices described at this manual are class A products. In domestic environment this products
may cause radio interference in which case the user may be required to take adequate
measures.
Because 866C have internal power supply, follow these special precautions:
? Circuit breakers (overcurrent protection) must be a part of building electrical installation.
? Pull out power cord plug from outlet to disconnect programmer from mains. The outlet
must be placed near to programmer and must be easy accessible.
ISP (In-System Programming)
Definition
In-system programming allows programming and reprogramming of device positioned
inside the end system. Using a simple interface, the ISP programmer communicates serially
with the device, reprogramming nonvolatile memories on the chip. In-system programming
133
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
84702-0008
CONN RECEPT ETHERNET 8-8 PNL MNT
848A
MEMORY PROGRAMMER PARALLEL INTER
85506-0001
CONN MOD JACK VERT 8-8 HI-SPEED
85507-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-0001
CONN MOD JACK VERT 8-8 SHIELDED
85508-5001
CONN MOD JACK 8POS T/H HI SPEED
85511-0001
CONN MOD JACK VERT 8-8 HI-SPEED
862015-1
6 POS RECEPTACLE
相关代理商/技术参数
845
功能描述:程序设计器 - 基于通用和内存 REORD 615-865 UNIV. WITH SOFTWARE
RoHS:否 制造商:Xeltek 产品:Universal Device Programmers 工具用于评估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口类型:Parallel, USB 工作电源电压:90 VAC to 250 VAC
845 1 1/2"X15YD
功能描述:SCOTCH BOOK TAPE 845 1-1/2 IN X 制造商:3m 系列:* 零件状态:在售 标准包装:24
845 3"X15YD
功能描述:SCOTCH BOOK TAPE 845 3 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:12
845 4"X15YD
功能描述:SCOTCH BOOK TAPE 845 4 IN X 15 Y 制造商:3m 系列:* 零件状态:在售 标准包装:8
845 PRO4
制造商:Micro-Star International 功能描述:845 P4 S478 SDRAM LAN - Bulk
845 PRO4-L
制造商:Micro-Star International 功能描述:845 P4 SKT478 ATX SDRAM - Bulk
845 ULTRA
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk
845 ULTRA-DF
制造商:Micro-Star International 功能描述:845 SKT-478 P4 DDR ATX AUD - Bulk